Features:
• Side lit dial face
• Digital hour meter
Includes: 10-60 mph speedometer, 7K tach/hour meter, trim meter, volt meter, fuel gauge.
Requires Faria instrument harness for installation, Part No. 32103-ZW7-000AH.
Connects Faria 5 gauge set plus optional water pressure gauge to main harness. 54 inches long.
Includes: Pressure tubing.
Includes: Digital hour meter.
Includes: Removable black square bezel.
Matches 5 gauge set dial face. Includes: Pressure tubing and fitting.
Includes: 10-60 mph speedometer, 7K tach/hour meter, trim meter, volt meter, fuel gauge. Requires Faria instrument harness for installation, Part No. 32103-ZW7-000AH.
Connects Faria 5 gauge set plus optional water pressure gauge to main harness. 54 inches long.
Intended for pontoon applications.
Includes: Pressure tubing.
Includes: Removable black square bezel.
Includes: Digital hour meter.
Note: Same as 37250-ZW5-010ZA only with no hour meter.
Matches 5 gauge set dial face. Includes: Pressure tubing and fitting.
Notes:
1. Dual engine application would typically use two tachometers and one speedometer gauge. The fuel management portion of the speedometer supports two source signals, one for each engine. Two gauge harnesses required for dual engine application.
2. Separate digital gauge harness supports one tachometer and one speedometer.
3. Fuel management information is sent directly from the engine ECU. No paddlewheel/fuel line sensor is required.
Gauge provides the following information:
• Speed
• Fuel tank level indicator
• Battery voltage
• Trip meter (miles)—resettable
Fuel management:
• Fuel flow—gph (includes totalizer)
• Fuel economy—mpg
Water in fuel alarm (from separator in engine) except BF115
Does not come with speedometer tubing. See below for pressure tubing.
Gauge provides the following information:
• Tachometer
• Trim meter
• Hour meter (shows total hours)
• Odometer (hours)—resettable
Indicator light display includes:
• Oil pressure alert
• Overheat alert
• ACG warning
• PGM-FI (check engine) warning
Matches the face plate of the Honda digital speedometer and digital tachometer. Includes pressure tubing and engine fitting.
10 foot long extension harness connects the 6 pin connector on the 20 or 23 wire engine main harness at the helm to the digital gauge harness. Allows digital gauges to be mounted in a remote location.
Connects to new 7 wire key switch panel harness. Supports both digital tach and speedo as well as analog gauges. Both analog and digital gauges can be used separately or in combination with each other. This harness will allow digital gauges to show analog functions on nondigital engines (same as standard 5 gauge set as well as PGM-FI indicator lights). Standard analog gauge harness plugs into separate 4 wire pigtail provided. 32540-ZY3-800AH
Enables the rudder indicator gauge function.
Connects any speedometer to the pitot tube on the engine gearcase, transom mounted pitot tube or pitot tube connection at the front grommet. Heavy wall construction.
Resettable. Note: Does not work with BF25- 50A4 tiller handle models.
Allows mounting the standard Honda original equipment tachometer, key switch, trim meter and instrument light switch.
Note: Requires standard wire harness A for connection. Intended for LHTA models.
Black face, flat lens tach. Tachometer only - no hour meter.
Kit includes Faria tach/hour meter, trim meter and Faria connecting instrument harness. Only available in black face, flat lens.
This brass fitting screws into the port (remove plug first) on the powerhead for water pressure source. This is a British Pipe Thread which conforms to the factory thread on the designated engines. Always use 2 wire ties to secure tubing to this fitting.
1⁄8 inch National Pipe Thread to British Standard Pipe Thread to install 1⁄8 inch hose barb included with water pressure gauge.
Low water Intake Screen set used on standard and Sabre™ gear cases. Uses original equipment mounting hardware. Allows the outboard to be run at a higher position while minimizing the top of the exposed screen from drawing air into the cooling system.
Uses original equipment mounting hardware. Allows the outboard to be run at a higher position without drawing air into the cooling system through the top of the exposed screen.
May be needed to install the smaller diameter original equipment tachometer in the standard 3 3⁄8 inch hole. Kit contains two black anodized aluminum bezel rings, needed for front and rear of mounting panel.
Connects original equipment tachometer, trim meter, and harness ‘‘B’’ tomain harness or side mount control box. 54 inches long.
Provides additional connection to harness ‘‘A’’ for speedometer, hour meter and volt meter.
Features:
• Fog free lens coating
• Back lit dial face
• Digital hour meter
• Engine on Demand Technology only logs hours on hour meter when engine is running
Includes: 10-65 mph speedometer, 7K tach/hour meter, trim meter, volt meter, fuel gauge.
Requires Teleflex instrument harness for installation, Part No. 32200-ZW7-000AH.
Connects Teleflex 5 gauge set plus optional water pressure gauge to main harness. 54 inches long.
Intended for pontoon applications. Includes: Pressure tubing.
Includes: Pressure tubing.
Includes: Pressure tubing.
Includes: Digital hour meter.
Matches 5 gauge set dial face. Includes: Pressure tubing and fitting.
Includes: 10-65 mph speedometer, 7K tach/hour meter, trim meter, volt meter, fuel gauge. Requires Teleflex instrument harness for installation, Part No. 32200-ZW7-000AH.
Connects Teleflex 5 gauge set plus optional water pressure gauge to main harness. 54 inches long.
Intended for pontoon applications. Includes: Pressure tubing.
Includes: Pressure tubing.
Includes: Pressure tubing.
Includes: Digital hour meter.
Matches 5 gauge set dial face. Includes: Pressure tubing and fitting.